IP
UDP
TCP
HTTP
cisco certification 200-125 ccna exam preparation with practice questions and Answers
At Which layer of the OSI Model does packet switching and path selection occurred
Physical Layer
Data Link Layer
Network Layer
Application Layer
Data Link Layer
Network Layer
Application Layer
Which command use to set default gateway in a Cisco switch
ip default-gateway
ip default-network
default-gateway
ip default-network
default-gateway
Which protocol uses tcp port 21
STP (spanning tree protocol)
FTP (File Transfer Protocol)
TFTP (Trivial File Transfer Protocol)
FTP (File Transfer Protocol)
TFTP (Trivial File Transfer Protocol)
Which Command Encrypt all password in plain text in a Cisco router or witch
service password-encryption
service-password encryption
enable secret
enable password
service-password encryption
enable secret
enable password
What are Two Method use by RIP Routing protocol to avoid Routing Loops
Split horizon rule
Maximum Hop Count
Spanning tree protocol
Elect DR and BDR
Maximum Hop Count
Spanning tree protocol
Elect DR and BDR
Which Command Enable debug PPP CHAP Authentication
debug chap authentication
debug ppp chap authentication
debug authentication
debug ppp authentication
debug ppp chap authentication
debug authentication
debug ppp authentication
Select the Valid IPv6 address
2031:1201:100F:0:9C0F:0
2021:0:130F:8F00::7524
2001::090F:AB00::2535
2003:W192:B40F:AF00::G924
2021:0:130F:8F00::7524
2001::090F:AB00::2535
2003:W192:B40F:AF00::G924
Which Protocol is used to Share VLAN Configuration information Between two Cisco Switches?
Spanning Tree Protocol (STP)
Dynamic Trunking Protocol (DTP)
Router Information Protocol (RIP)
Dynamic Trunking Protocol (DTP)
Router Information Protocol (RIP)
Which Routing Protocol use Multicast address 224.0.0.9 to send Routing Updates
RIPv2
EIGRP
OSPF
IS-IS
Which items are correct about the routing protocol OSPF(Choose Three)
OSPF use Hop Count as Metric
it supports VLSM
Area 0 is Called Backbone Area
Process id has to be match in all routers
Which of the Following is a Correct Default Route
ip route 192.168.10.0 0.0.0.0 serial 2/0
ip route 0.0.0.0 172.16.30.2 192.168.20.2
ip route 0.0.0.0 0.0.0.0 fastEthernet 1/0
ip route 10.0.0.0 0.0.0.0 192.168.10.2
ip route 0.0.0.0 172.16.30.2 192.168.20.2
ip route 0.0.0.0 0.0.0.0 fastEthernet 1/0
ip route 10.0.0.0 0.0.0.0 192.168.10.2
Subscribe to:
Posts (Atom)
Popular Posts
-
The destination network no longer exists. The destination network is moved to a different interface on the same router. The path between ...
-
Users who attempt to connect to the console port of the router must enter a password. The entries permit access through the console by the ...
-
The router will install the first route it learned into the routing table. The router will install both routes in the routing table and lo...
-
It prevents the synchronization of routing updates by buffering the updates as they leave the router interface It prevents the synchroniza...
-
HA DRS FT Storage DRS
-
Refer to the exhibit. What two commands will change the next-hop address for the 10.0.0.0/8 network from 172.16.40.2 to 192.168.1.2? (C...
-
R001 : VMware HA must be functional. R002 : VMware SRM can be used between two sites for DR processes. R003 : You must be able to see all ...
-
Router(config)# hostname Admin Admin(config)# enable secret cangetin Admin(config)# interface fa0/1 Admin(config-if)#ip address 192.168....
-
If RouterC receives a packet that is destined for 10.5.1.1, it will be forwarded out interface Fa0/0. If RouterA receives a packet that is...
-
Keep the existing static route and configure a new static route with the correct next hop IP address. Negate the existing static route and ...